InspectionWare Release Build: Version 12.518.0 (64 bit) | Build Note: Overhauled the utility tasks on Overlay Annotation. New Features: (1) A Rendered Beam in Reflector Response mode computes a map from several beams with a reflector or Elevation Spread up to 40 times faster, and the Phased Array Reflector Response and TFM Reflector Response with Elevation Spread on are faster too. (2) A Sweep C-Scan built on a Sweep Correction with Apply Model Correction on now measures the corrected sweep in its amplitude and time-of-flight outputs. (3) Added Weld Profile.Has Weld. Turning it off describes a part by its Piece, Clad and Slopes properties alone, with no weld, caps or heat affected zone, and hides the weld properties. (4) Choices in a list or combo property can now each show an Image Library picture, in property grids and in a Combo's drop down. Give a stored variable its pictures with the Choice Images attribute in Edit Variables, Set Variable Attribute() or the Choice Images parameter of SetAsList() and SetAsCombo(), or give one control its own with Combo.Choice Images. (5) A device-conversion launch the GPU backend refuses falls back to the CPU conversions for the rest of the execute, and sources of 65536 or more A-scans convert on CUDA. (6) The DirectX source and output conversions dispatch without the watchdog chunking, which drained the GPU up to 33 times per plane. (7) The Generic Total Focuser gains the GPU Conversions property and the Conversions On GPU indicator, which now reports None when every plane fell back. (8) The Total Focuser's CUDA graphs are recorded the second time a plane's plan is seen and kept 128 deep, so an execute whose planes all differ, such as a Generic Total Focuser selecting a map layer per plane, runs the direct path instead of recording a graph per plane; a few failed recordings in a row, not one, turn the graphs off. (9) The Total Focuser's device-conversion buffers no longer allocate GPU memory they never use: on CUDA its raw source and converted output buffers hold no cudaArray and no mask, and on DirectX its raw source buffers hold no readback staging buffer. (10) The Total Focuser builds images up to six times faster on AMD and Intel GPUs. (11) The Total Focuser's DirectX backend builds images with Allow Map Interpolation on and Map Interpolation = Bilinear up to 11aster on AMD GPUs. (12) The Total Focuser no longer reconstructs scan positions whose A-scans hold no known sample, such as the padding Unify Scan Axes adds before and after a scan, and writes them as unknown; PWI Scan Data builds up to 6aster with identical images. (13) Added the View Mode planes XY, YX, ZX, YZ, ZY, XZ, XNegY, NegXY, NegYX and NegZX to Simulator Display.Set View Point(). (14) The Side view of Simulator Display and I3D Part Editor now puts Z to the right and Y up, instead of Y to the right and Z up. (15) Image selection properties now allow selecting from a short dropdown, or a more detailed Image Library pop-up. (16) The Simulation's cursor readout now shows the dB value of a Rendered Beam's beam field or Reflector Response map under the mouse. (17) Added Rendered Beam.Wedge Path, which carries the Reflector Response map through the wedge or an immersion probe's water. (18) Added the Own choice to Rendered Beam.Palette, which each Rendered Beam takes when its rays have no palette. (19) Rendered Beam.Calculate Beam() now shows a progress dialog that can cancel a Reflector Response calculation. (20) The Total Focuser builds images up to twice as fast on the GPU when Output Caching is Partial or Output Type is SCF, VCF or NSI. (21) Rendered Beam now draws a Reflector Response and Beam Field on a Point Sources' rays, treating the points as a virtual array. (22) Added Rendered Beam.Recalculate when changed; a new Rendered Beam now computes its Reflector Response only when Calculate Beam runs. (23) Rendered Beam's Reflector Response can now follow its own Use Ray Set Modes, Modes and Mode To Show, kept apart from the Beam Field's. (24) The Total Focuser builds images faster on NVIDIA GPUs. (25) Added Mark Weld Face to Rays, which with Mode Selection Method Weld draws a dot where each ray enters the weld, shrinking with the angle of incidence on the weld face up to Rays.Interface Cut Off Angle. (26) Added By Firing Group to PA Rays.Draw Color Mode, which draws each beam's rays in a color picked by the beam's Firing Group. (27) InspectionWare Child Instance passes -NoInteraction on to its child, so dialogs no longer stop a silent Test Runner run. (28) Phased Array Reflector Response now warns when its Noise Floor is used with Amplitude set to Physical and the beams are recorded at different gains. (29) Total Focuser.Max Window Loss no longer keeps the A-scan long for pixels the image crops. (30) Point Sources.Fill From Primitive(), Fill From Rays(), Get From Position Data Set() and Copy Points From() without Append now set every amplitude back to 1. (31) Object script task arguments can now be expressions, such as nPages - 1 or "Item " + n. (32) Object scripts run up to twice as fast: a script reads the clipboard only when it names clipboard_object, and an expression binds only the names it uses. (33) A Rendered Beam's Reflector Response map now maps beams that resolve different Beam Set velocities, as an anisotropic material gives each beam's angle, when the rays' Use Beam Set Velocities is on: the element rays are traced once for each velocity and each beam is mapped with its own. Such maps were refused. (34) Added Beam Velocity Tolerance to the Rendered Beam: with the rays' Use Beam Set Velocities on, beams whose Beam Set velocities lie within this percentage of each other share one trace of the Reflector Response map's element rays, made at the middle of their velocities. The default is 0.5; 0 traces each velocity on its own. (35) Point Sources.Fill From Data() and Fill From Table() with Reset Point Count now set every amplitude back to 1, as the other fills do; Fill From Table() then applies its table's amplitude columns. (36) Object scripts can now branch and loop: if, else if and else run blocks on a condition, foreach runs a block once for each object a search spec finds, and return ends the script; an indented comment line or a line of spaces no longer makes the statement after it fail. (37) Added Wave Model to the Rendered Beam's Reflector Response: Continuous Wave, the default, maps a steady wave as before, and Pulse fires a pulse of the probe's Bandwidth, so a beam's elements add only where their arrivals lie within the pulse and a grating lobe drops to what a short pulse gives while the main beam stays as it was. (38) Phased Array Reflector Response now warns when its beam set is a matrix capture, which it does not model, and when the beam set has no Tx Delays while its beams still hold earlier ones. (39) Added Rendered Beam.Leg Pairs and Rendered Beam.Normalize Legs, to map the legs a Total Focuser output images, alone or combined. (40) Added a Weld Region choice to Rendered Beam.Defect Type, which maps the weld's fusion faces and the reflectors in the weld. (41) Added Build Panel Layout task to Processor Package, User Defined Node and Structured File, which builds the package's panel from the properties, tasks and data you choose. (42) With Wave Model set to Pulse, a Rendered Beam's Reflector Response now weights each element's rays by its directivity averaged over the pulse's band rather than at the centre frequency alone, so a beam steered near an element's null is no longer lost: at 80 percent bandwidth the first null fills in to about a tenth of the element's strongest. (43) Wave Model of a Rendered Beam's Reflector Response now defaults to Pulse, and a Rendered Beam saved before Wave Model existed takes Pulse too, so its map changes wherever a beam sums its elements coherently: set Continuous Wave to have the map as it was. (44) A Rendered Beam's Reflector Response with Wave Model set to Pulse now computes several times faster: a sweep of 31 beams mapped round trip takes about a fifth of the time, and with a reflector about a sixth. (45) Added Send To Point Cloud task on Weld Zones. (46) Added support for named surfaces on cross-section primitives. (47) Added segment name support for plate and pipe cross-sections. (48) A Part Follower set from Probe Configuration's Probe Position On Extruded now rides the Upper, OD or ID Section and reads the Probe Configuration's positions. (49) A software licence that may not be used offline now closes InspectionWare when the licence server cannot be reached. (50) Added "On Key Down" option to an On Control Event on a Data Plot. (51) A Duet Device firing on its timer now reports its connection as lost when its data stops arriving for 10 cycles or 3 s, whichever is longer, instead of silently collecting nothing. (52) Added Limit Rate To Max Data Rate to Duet A Scans, which lowers a timer-fired Idle or Scanning Acquisition Rate so the data stays below the Duet Device's Max Allowable Data Rate and the Duet no longer stops streaming part way through a scan. (53) Renamed Total Focuser.Prepare Maps If Needed to Total Focuser.Always Prepare Maps; workspaces and scripts that use the old name still work. (54) Added Indications to Rendered Beam.Defect Type, which draws the indications the probe's plane crosses without needing a weld. (55) Added support for STEP assembly structure entities and improved surface/edge loop handling. (56) Color plots now draw undefined points in a Palette's Special Colors, picked by an Aux Data Object on the data. (57) The Rendered Beam's Reflector Response error for a beam whose transmit and receive sides resolve different velocities now gives the velocities' units. (58) Beam Tool Control now hosts BeamTool 12. (59) The AOS Waveform Channel digitizes each beam only over the A-scan range its UT Beam Set shows, such as the ranges Total Focuser.Calculate Beam Ascan Lengths() sets, which lowers the data rate. (60) Added Evident HDF 4p0.Load Offsets As, which chooses the channel offsets an imported probe's offsets go into. (61) Added Move Scan Offset To Channel and Move Index Offset To Channel tasks to UT Beam Set. (62) Added SetConventionalBeamOffsets to set U and V coordinate offsets for conventional groups, adjusting for wedge offsets and data mapping grid. (63) Refactored BuildProbeConfigFromDataGroupValues to only clear and set channel offsets for pitch probes, preserving offsets for catch probes in pitch-catch pairs. (64) The error shown when an HDF file holds more data than its description declares now names the dataset and gives both sizes. (65) Added Connect Events By Task List task to Processor Package, which connects each Object Event to the Task List rows tagged with its name. (66) Added a Task List choice to Variables.Variables Role, whose rows name tasks of objects for the new Run Task task to run. (67) The TD Focus Waveform Channel error for receivers it cannot acquire in one shot now says which channels of a 256-element Gen 3 instrument can receive together. (68) Added Anisotropic Rays to PA Rays, Point Sources and Ray Traced Element Times Map, which skews simulated rays in an anisotropic part. (69) Added Add Control Bar task to Tab Control and Control Bar.In Tab Row, which put a Control Bar at the right end of the tab row, beside the tabs. (70) Added a Color With Automatic Edit Style to Variables, which adds Automatic to a color variable's picker. (71) TD Focus works with both TD focal law converters: FLawConvert64 4.14 and newer, which can receive on both acquisition cards of a 256-element Gen 3 instrument in one shot, and the older ones. (72) Added Labels to Overlay Annotation's draw script items. (73) Added Performance Analyzer tasks to the Developer toolbar under the Record sub-list. (74) From Overlay Annotation task on Rotated and Extruded now takes the Annotation's labels as Segment Names. Bug Fixes: (1) A TD Focus Waveform Channel using hardware FMC now fails to compile with an error when the instrument cannot receive on all its receive elements in one shot, instead of compiling and collecting no data. (2) Fixed a TD Focus instrument staying idle, with TD Focus A Scans.Actual PRF at 0, after a compile failed. (3) Fixed a Linear Array resetting its element sizes whenever an element, body or focusing property was changed: Linear Array.Element Width Y fell to 1 and Linear Array.Element Width X to Linear Array.Element Pitch X, so the elevation and the gap between elements could not be edited. (4) Fixed Apply Model Correction with Merge Data Mode set to Max Abs turning a strongly boosted negative sample into the most negative value. (5) Fixed the DirectX Total Focuser reading every fourth sample of an 8-bit source from the wrong byte when Ascan Precision is Float16 and GPU Conversions are on, which lowered the image by about a quarter. (6) Fixed changing Combo.Combo Style having no effect until the workspace was reopened. (7) Fixed the GPU dispatcher reading past the end of an older GPU backend's function table, which could call a garbage address when a newer fpNDE ran with a backend DLL built before an entry was appended. (8) Fixed a Simulator Display connected through a connection point going on drawing the previous simulation's parts and probes beside the new one's after the point was bound to another simulation. (9) Fixed an Execute Object Script whose target is reached through a connection point still running on the object the point was bound to when the script was last compiled, after the point had been bound to another object. (10) Fixed Set Properties and other linked properties failing with "Failed to find property Logging" when they set a Message Logger setting that now belongs to its Diagnostics Log. (11) Fixed a product install putting Microsoft.Extensions.Configuration.Binder.dll in the program folder instead of the install folder chosen in the setup dialog. (12) Fixed Rendered Beam reflector responses failing for an immersion probe placed without a Part Follower, such as one moved by motion axes. (13) Fixed UT Beam Set turning off matrix capture when a Sectorial or Linear sweep's First Element or Aperture is edited. (14) Fixed InspectionWare crashing when saving to a full drive; failed saves now show a warning and keep the existing file. (15) Fixed InspectionWare leaving no crash dump when it closed on an unhandled error or its install drive was full. (16) Fixed TrueFocus Builder.Configure Strip Charts() leaving out the TFM plots of a package that reconstructs only the envelope. (17) Fixed the Total Focuser keeping out of date travel time maps, or failing to compile, after a beam set's aperture, steering or number of beams changed while Prepare Maps If Needed was off. (18) Fixed errors in the reflector responses of Rendered Beam, TFM Reflector Response and Phased Array Reflector Response, and in the model corrections Total Focuser and Sweep Correction take from them. (19) Fixed Point Sources.Configure For FBH() weakening its single ray, which a cutoff of 0 gives, by the square root of the number of points. (20) Fixed the Rays table showing the wrong Next Solid Role for a ray that runs straight through a face between two solids into a weld. (21) Fixed Total Focuser.Apply Model Correction having no effect while Total Focuser.Normalize Weighting is on. (22) Fixed TFM Reflector Response and Phased Array Reflector Response modelling a Defect Angle or FBH Inclination as its mirror image on contact probe and pipe views. (23) Fixed Remote Workspace Test hanging instead of finding its child instance; it now fails if the child exits or Remote Workspace Test.Timeout Tick Count runs out. (24) Fixed SVG images on a Button being drawn left of centre, which happened since 12.515. (25) Fixed TFM Reflector Response and Phased Array Reflector Response taking a skip leg's backwall reflection on a pipe at a different angle from its wedge transmission. (26) Fixed a semicolon inside a quoted string or a comment line ending an object script statement. (27) Fixed an object script running a task when one of its arguments could not be evaluated. (28) Fixed object script expressions reading the previous value of a property named in them, such as an unsigned colour, on every run after the first. (29) Fixed a Rendered Beam's Reflector Response map ignoring Use Beam Set Velocities, so the map and the rays over it could be traced at different part velocities. (30) Fixed Execute Object Script passing extended property and table values to its script rounded to six decimal places, cut to 32 bits or with leading and trailing spaces removed. (31) Fixed a Rendered Beam's Reflector Response map keeping a plane of sums for every pair of legs when all its beams share one velocity, and its Trace Summary not saying when Beam Velocity Tolerance merged beams or that the range of a map traced at several velocities is fitted to the middle one. (32) Fixed beams calculated with the PeakNDT focal law calculator getting the wrong X Offset when Windows uses a comma as its decimal symbol. (33) Fixed Simulation.Convert Units() changing a probe's Frequency and Bandwidth, and scaling a Linear Array's Element Width X and Element Pitch X twice. (34) Fixed Use Beam Set Velocities applying the Probe Configuration's velocities in the wrong units when the Simulation's Units differ from the Probe Configuration's. (35) Fixed Duet A Scans failing to start acquiring when the firing type is External. (36) Fixed InspectionWare crashing when a Total Focuser processes a very large scan. (37) Fixed UT Beam Set giving a different aperture when a Single Beam or Single Beam Pitch Catch sweep's First Element and Aperture are set in the other order. (38) Fixed the Total Focuser keeping out of date travel time maps after a Probe Configuration, output mode or skip, or travel time map setting change when its maps are not prepared on every compile. (39) Fixed the Rendered Beam in Simulations whose Units are cm, m or thou, which was calculated as if they were mm. (40) Fixed UT Beam Set refusing First Receive Element, Receive Aperture and Tx Rx Offset Lock moves on a catch probe whose elements are numbered after the transmit probe's. (41) Fixed UT Beam Set turning off matrix capture when a Single Beam or Single Beam Pitch Catch sweep is edited or recalculated. (42) Fixed a probe added to a Simulation in inches, cm or m keeping its element pitch, Separation and focal lengths in mm. (43) Fixed the MCP tool iw_cs_searchSourceCode returning no matches when a search found 20 or more lines. (44) Fixed rays that miss the part being drawn 25 m long in a Simulation in metres, and backwards in a Raytracer's Raytrace All and background beam calculation. (45) Fixed rays that miss the part being 25 inches, cm or m long outside the Raytracer, which moved C Scan Renderer points in Simulations not in mm. (46) Fixed TD Focus.Model showing Gen 2 for a Gen 3 instrument. (47) Fixed the TD Focus Waveform Channel error for too many receivers in one shot wrongly blaming FMC Type 1; it now names the focal law converter version and the Front Panel Type. (48) With GPU.Backend set to Automatic, InspectionWare now uses DirectX on an NVIDIA GPU its CUDA code cannot run on, and GPU.CUDA Status says why. (49) Fixed a crash when an Execution Script run from a button or task was recompiled while it was still running. OverviewThis document contains a downloadable Windows installer for InspectionWare as well as the release notes covering the current version.
Hardware requirements
Additional resources After downloading the installation files you may also want to review/download the following resources: Download and Installation Instructions
The following file links will become active once the required information is submitted: Downloads InstallInspectionWare64 12.518.0.exe (139.2 MB) Release Notes.txt (296.2 kB)
|
Print Email page
Share
|